Faze V2 von Hobbyzone

Features

• 12,2 g leichter Quadcopter
• Integrierte LEDs
• Auto-Flip-Funktion
• Robuster Body für optimalen Schutz
• Kompakte 2,4GHz-Fernsteuerung
• Wiederaufladbarer und austauschbarer 100mAh LiPo-Akku
• USB-Ladekabel
• 2 Stk. AAA-Batterien enthalten
• 4 Ersatzrotorblätter enthalten 

Flight Control SP RACING F3 EVO_BRUSHED

Flight Control SP RACING F3 EVO_BRUSHED

Specification:

Item Name: SP RACING F3_EVO_BRUSH flight controller for indoor-FPV  

Dimension: 22mm*32.5mm
Thickness: 1.2mm

Weight: 3g

Features:
1. F3_EVO_Brush revision is out of the F3 EVO SP RACING is based on a SP RACING F3 EVO firmware 32 brush flight control.
2.The flight control support 1S (4.2V) and 2S (8.4V) power supply, 2S power can bring flying experience more violence.
3. Independent design of the circuit structure, comes with the pressure reduction technology, whether it is 1S or 2S power input, UART1/2/3 output 5V,  DSM port output 3.3V
4.Using STM32F303CCT6 + MPU6500, advanced hardware platform F3 guarantee more stable flight
5. With a large current NMOS transistors, operating current of up to 10A or more. Each Brushed motor is equipped with freewheeling diodes.
6.Support for PPM, SBUS, DSM receiver input signal.
7. With battery voltage detection and buzzer interface.

Micro USB socket: Connect to computer to flash firmware and configure the flight controller

M1/M2/M3/M4:Connect to Coreless motor

VCC/GND: Connect to the battery 1s~2s input (Configure by the voltage input pad)

UART1: GND +5V RX1 TX1 , Could connect to GPS/OSD

UART2: GND +5V RX2  PPM/SBUS Receiver input（RX2）

UART3: GND +5V RX3 TX3  Could connect to GPS OR Telemetry module ,could not use when DSM/DSM/DSMX Receiver Used

BUZ+ -: Connect to a external buzzer

DSM/DSM2/DSMX: 3.3V GND RX3 DSM/DSM2/DSMX Receiver input

LED Strip could connect to WS2812 LED Board and configure it in Cleanflight or Betaflight

Receiver configuration:

1. DSM receiver soldered directly to the DSM/DSM2/DSMX Receive interface 3.3V, GND, RX3. Enable Seria_RX for UART3 and Set Receiver mode RX_SERIAL ,Select Spektrum1024(DSM/DSM2) or Spektrum2048(DSMX) in Cleanflight Configurator.

2. SBUS receiver welded to the UART2 GND, + 5V, RX2 . Then Enable Seria_RX and Set Receiver mode RX_SERIAL ,Select Sbus signal in Cleanflight configurator.

3. PPM receiver welded to the UART2 GND, + 5V, RX2 .Then set Receiver mode to RX_PPM in Cleanflight configurator.
 

Notice:

Before applying power, pay attention to the battery voltage selection.
The default setting is 1S (4.2V); if you use 2s lipo, please first need to disconnect pin2 and pin 3 and then solder pin 1 and pin2. Prohibit the same three pads shorted together.

FIRMWARE FLASH  -F3 EVO_Brush

The following tutorial covers flashing Cleanflight Firmware onto the F3 EVO_Brush Flight Controller. Betaflight is the same steps like Cleanflight.

Installing the ST drivers:

(For Windows Only)

Download and install the DfuSe demo package.

Open an explorer window and browse to (assuming you’ve installed to the default path) C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.5\Bin\Driver

Browse two folders deeper to the folder relative to your Operating System version, and x86-32bit or x64-64bit variant.

Click the dpinst_x##.exe to install the driver.

Installing Cleanflight Configurator:

(For Windows Only)

You must use Cleanflight Configurator v 1.0.0 or newer.

The following assumes you also have the Chrome Browser installed.

Get the latest Cleanflight Configurator (+ Add to Chrome)

Replacing the ST Driver with WinUSB driver:

(For Windows Only)

1. Plug your F3 EVO_Brush board onto your computer. Open cleanflight configurator , you should see the serial com port

2. Click “Firmware Flash” menu, select the latest firmware for F3 EVO_Brush and load firmware [online] or load firmware [Local]

3. Click “Flash Firmware” and wait the ST DFU DRIVER Automatic installation. It’s successfully installed when you see the DFU port on the Up right corner.

4. Download and launch Zadig
5. From Zadig, a.) Select Options, b.) Tick List All Devices

6. a.) Select STM32 Bootloader from the dropdown, b.) Choose WinUSB as the replacement, c.) Click Replace Driver. Some times the Replace progress will be slow or no response, you can close it and do it again, you will find the dropdown is no STTUB30 but WinUSB, just click replace driver from WinUSB to WinUSB .

* Credits for the Zadig option – Cleanflight Docs

Flash Firmware

Go back to Cleanflight configurator and Click Flash Firmware , again after the Driver replace completed, and you will see the firmware flashed successfully!

Warnings!

This F3 EVO_Brush flight controller is only use for BRUSH MOTOR, Not compatible for BRUSHLESS MOTOR

Lipo-Akku 3,7 V 700 mAh 25C

JJPRO-T1 95mm RC Quadcopter Spare Parts Frame Kit

Simulator 16 in 1 R/C

Support:
FMS, XTR, realflight G2.0 G3.0 / G3.5/G4.0/G4.5/G5.0/G5.5, AeroFly 5.5, PhoenixRC 1.0/3.0/2.5/2.0/4.0, and VRC2

Packing content:

1. USB 16 in 1 simulator x1
2. JR / Walkera /Spektrum and other audio cable × 1
3. Futaba adapter cable × 2
4. ESKY adapter cable × 1
5. CD x 2
6. USB cable x 1

Turnigy nano-tech 300mah 2S 35 ~ 70C

Sentinel School Black

4pcs propellers for JJRC H36 can be used on Blade Inductrix

Inductrix 200mAh 1s 3.7V 45C LiPo Battery

Spares Parts Frame For Blade Inductrix