MarkOne Beacon V3.0

Specifications:
Detection Range: 15+ meters (Detection Characteristics PDF)
Beam Angle: ~70 degrees
PCB Dimensions: 100x50x8mm
Dimensions File: MarkOne2.dwg
Voltage Input: 10.2-14V (suitable for 3 cell lipo)
Power Consumption: 0.25A @ 12V
Power Connector: 2 Pin JST PH (S2B-PH-SM4-TB(LF)(SN))

Package Includes: 
1x MarkOne V3.0 Beacon 
1x Female JST PH Cable (14cm)

Here Flow

The HereFlow optical flow sensor is a lightweight optical flow sensor including a short range lidar which uses the CAN protocol to communicate with the flight controller. This can be used to improve horizontal position control especially in GPS denied environments.

ADS-B Carrier Board

Drone pilot ground radio station (GRS)

Intel Edison Carrier Board including PSM without the cube and Edison Chip

The "Full" carrier board allows you to break out the full functionality of the Cube.

It doesn't contain a Intel Edison Chip. Please visit other online stores for purchasement.

It also comes with all the correct components to directly plug in an intel edison.  use the edison for off board computing.

Pixhawk Airspeed Sensor Kit

Pixhawk Airspeed Sensor Kit -Digital

433Mhz 500mw Telemetry Set Compatible PX4 & APM

*Note: This is not an original 3DR brand product.

433MHz Radio Wireless Telemetry System comatble with Pixhawk and APM Flight Controller

The Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios. It’s available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).

The system provides a full-duplex link using HopeRF's HM-TR and data modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.

The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters. Firmware upgrades and configuration are fully supported in the APM Mission Planner . Configuration is also possible through the 3DR Radio Configurator or AT commands.

Included with this product:

•2 x "Radio Moden 433Mhz "Air" module"
•2 x "Telemetry Cable"
•2 x "Antenna 433MHz RP-SMA 2dBi"

•3DR Radio Configurator

•DOCUMENTATION, SET UP AND COUNTRY COMPATIBILITY

Hardware features and specifications:

•Very small size
•Light weight (under 4 grams without antenna)
•433MHz variants
•Receiver sensitivity to -121 dBm
•Transmit power up to 20dBm (100mW)
•Transparent serial link
•Air data rates up to 250kbps
•MAVLink protocol framing and status reporting
•Frequency hopping spread spectrum (FHSS)
•Adaptive time division multiplexing (TDM)
•Support for LBT and AFA
•Configurable duty cycle
•Built in error correcting code (can correct up to 25% data bit errors)
•Demonstrated range of several kilometers with a small omni antenna
•Can be used with a bi-directional amplifier for even more range
•Open source firmware
•AT commands for radio configuration
•RT commands for remote radio configuration
•Adaptive flow control when used with APM
•Based on the HopeRF HM-TRP radio module, featuring an SiLabs Si1000 RF microcontroller.

*Note: This is not an original 3DR brand product.

2.4G Radio Signal Booster Amplifier For DJI Phantom Transmitter FPV Extend Range

FrSky Smart Port Air Speed Sensor ASS-100 is designed for FrSky Smart Port enabled system, and can provide Airspeed Data for your entire flight.

Compatibility    

FrSky Smart Port enabled receivers, such as X8R, X6R, X4R, etc.

Model    

ASS-100

Dimension    

Circuit Board: Weight 5 g, dimensions 33.14×17.14×10.45mm

Pitot Tube: Weight 4 g, length 101mm, diameter 2.6 mm

Pitot Tube Hose: Silicon, clear, 3 feet (1 meter), 2.2mm ID, 3.8mm OD

Operating Voltage Range    : DC 4 -10 V

Operating Current: 25mA@5V

Measurement Range    : 0~360km/h  (0~223.7mile/h )

MANUAL

3DR Cable Pack