EzAntennaTracker v2

The innovative ImmersionRC Antenna Tracker performs the almost magical task of following your model around the sky, pointing a high-gain directional antenna directly at your model.

This is the second revision of the Antenna Tracker, featuring an integrated power supply to power the servos, a video buffer, and a single-cable hookup to ImmersionRC's Uno, and Duo A/V receivers.

13dBi Circularly Polarized Patch antenna, Full-Custom design for the FPV market. 

Ideal companion to our 5.8GHz SpiroNET Omnidirectional CP antennas, ranges of several km on a CE-legal 25mW system very possible!

This 5.8GHz Circularly Polarized patch antenna was custom-designed, with no expense spared, for the FPV market. Light enough to be mounted directly onto an LCD headset, or directly onto the front of one of our Uno, or Duo receivers.
This antenna will breathe new life into the CE-Legal 25mW systems, allowing multi-km range with ease.  For 600mW systems, its time to start worrying about the range of the control link, since with a combination of this antenna, and a spiroNET omni, the video range can greatly exceed the control range of most 2.4GHz radios.

Precision manufactured with very tight tolerances and 100% tested on a professional antenna tester (Rhode & Schwartz) to ensure maximum range and performance.

    SMA connector compatible with all FatShark/ImmersionRC 5.8GHz products sold to date.
    Right-hand circular polarization
    5.8GHz ISM Band
    13dBi gain
    Beam width 35 degrees (H + V)
    F/B Ratio 26dB
    VSWR < 1.5:1 (5740 - 5860MHz)
    Impedance 50ohms

- Dimensions: 92mm x 92mm x 10mm
- Weight: 54

SpiroNet 5.8GHz Patch Antenna LHCP

5.8GHz v3 600mW Tx immersionrc 100% fatshark compatible

The 600mW version of the 5.8GHz transmitter greatly increases the range of a 5.8GHz link, adding a margin of security over the 25/100mW version. Team up with a Duo5800 receiver on the ground, and enjoy noise-free video further than you can see your model.

• 600mW (27dBm, +/- 1dBm) of clean output power
• SMA Antenna connector, with supplied 5.8GHz Rubber-duck antenna
• Frequencies: 5740, 5760, 5780, 5800, 5820, 5840, 5860MHz
• Not affected by 2.4GHz R/C radios!
• -600mW (28dBm, +/- 1dB) of clean output power
  -SMA female antenna connector.
  -Frequencies: 5740, 5760, 5780, 5800, 5820, 5840, 5860MHz
  -Onboard quiet switching regulator, powers 5V cameras
  -Input voltage range: 6 – 25V (2S-6S)
  -Not affected by 2.4GHz R/C radios!

ImmersionRC SpiroNET v2 5.8GHz SMA Diversity Bundle (2 antennas)

While it is not a new design, the SpiroNET range has proven to offer the best reception in the entire band of 5.8 ghz, so you can be sure of any channel.

Package Included
1 x SpiroNET v2 Omni Headset antenna, with right-angle SMA
1 x SpiroNET 8dBi LHCP Patch
1 x 45 degree SMA adapter, for patch mounting.  

Immersion TrampHV EU Version

The most advanced 5.8GHz Video Transmitter available today. Only 4 grams, and a slender 31 x 20mm, the TrampHV is also the smallest direct LiPo-powered vTx in the business. 

Supporting touch-free 'TNR' wands, for low inter-heat times, and full Tx configuration with a bright OLED display

From the team that invented the now ubiquitous RaceBand, comes the Tramp HV, the most advanced 5.8GHz Video Transmitter in the business. 

* The EU Version is identical to the International, and USA versions, with one exception. The firmware is region-locked to prevent transmission outside of the EU ISM band. All ImmersionRC/FatShark channels are still available, along with 6 of the 8 RaceBand channels. Power output is limited to 25mW also to meet EU RTT&E Regulations.

- Smallest direct LiPo powered vTx in the business.
- TNR Touch-free wand control
- Traditional button+LED control of frequency and power
- 1mW -> 600mW+ linear power control
- All 40 standard channels
- Built-in thermal protection
- Factory power normalization
- Glitch-Free frequency changes
- Micro-power pit mode
- Additional channels for race events (Race Wand only)
- Retail regional locking without opening package

5G8RX 32ch Race Band RX

Vortex Metal Motor Mounts (2204)

ImmersionRC  Vortex Metal Arm Mount Upgrade

Precision CNC milled aluminum arm clamps, designed for the hard-core Vortex racer.

After upgrading with this kit, the Vortex arms no longer fold, but instead are very rigidly mounted to the frame. 

Includes:

- 8x Anodized, CNC Milled, Top Clamp

- 8x Anodized, CNC Milled, Bottom Clamp

- 18x Screw, M2x16

- 18x Screw, M2x5

Fatshark 5G8 32ch Race Band with dual SMA V2

FSV2445 5G8 32ch Race Band with dual SMA V2

Package includes 90 degree and 45 degree SMA adapters and white dual hole Dominator door.  Note that this is not a true diversity solution; it is an antenna diversity that combines the range benefits of an omni and directional antenna.  It does not reduce video breakup (other than the benefit of better signal strength of directional antenna) nor is the receiver suitable for flying at limits as in snow conditions it will switch between antenna looking for best signal.