M8N GPS for CC3D

FPV Flight Controller N3 OSD Module for DJI NAZA ,V1,V2, Phantom

- Available to display flight attitude, throttle level, flight mode and remote control signal (receiver should support RSSI).

Easy to directly read out the total data including gyro, barometer, electronic compass and etc. from bus data of NAZA.

- Same port with DJI Phantom MINI IOSD

- NAZA special OSD, no need PC parameter adjust

- Support NAZA GPS, read NAZA Compass and GPS data, could direct return direction in air

- Barometer, more precision height indication

- Three page selectable: Chinese/DJI-type IOSD/Self-definition

- Power supply from NAZA flight controller

Package included:
- FF OSD N3 *1
- Cable*2

DJI iOSD mini On Screen Display (Supports Naza-M & Wookong-M)

iOSD mini

• The Naza-M now supports iOSD Mini. This will undoubtedly give you a fantastic FPV flight performance. Depending upon DJI’s accumulation of historic and reliable information integration technology, the iOSD Mini can grab the most accurate first-hand flight data information in the shortest possible time.

• Voltage: 6V
• Working Temperature: -20℃~+60℃
• Video Input/Output Mode: PAL/NTSC(automatically recognize)
• Weight: 14g
• Working Current (Typical Value): 180mA@6V

Flight Control Naze32 with 10dof version with compass and barometer

NanJ 32 10dof Flight Controller

• 36x36 mm
• 3-axis MEMS gyro + accelerometer (MPU6050)
• Flexible motor outputs, support various airframe types
• Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal.
(Default is Quad-X)
• Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum Satellite receiver.
• Battery voltage monitoring
• Modern 32-bit processor running at 3.3V/72MHz
(STM32F103CB).
• Onboard MicroUSB for setup and configuration
• configuration software for easy setup
• rev4 hardware

* The difference between 10dof and 6 dof version are compass and barometer, the 6 dof version DOESN'T have HMC5883l and MS5611.

** NanJ 32 and Flip 32 are the same controller.

NANJ32-Manual.pdf

KISS FC - 32bit Flight Controller V1.03 Original

New version
- changed bootloader solderpads to a press button
- changed USB Port type



As we felt the need for a modern more simplified 32bit Flightcontroller, we made the KISS FC, which includes a complete own Flight Controll Firmware development who get rid of some old ballast, this took some time, but the result is very pleasing.
The Idea was to simplify some things and due to intensive long term testings of some pretty good Pilots we where able to optimize the code to a  point where you hopefully get your quad in the air quite quick.
Normally you just need to choose your Airframe in the GUI and are able to fly (at least with KISS ESC), otherwise you can download presets of well knowen Pilots for given configurations and of course can tweak the PID yourself over the GUI.
The software setup side is reduced as far we can, many things are allready taken in to account for you, if you bring some solid soldering skills you should be able to build your quad pretty quick.
A new feature is also the inbuild telemetry, in combination with our 32bit ESC line its possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI
This way you get usefull informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM.


Supported copter types:
- Tri
- Quad +/x
- Hexa +/x

Supported RX types:
- PPM Sum
- Spektrum Sat. (serial / DSM2 & DSMX)
- Futaba / Taranis SBUS
- Jeti ExBus
- Graupner SumD / SumO
- MultiPlex
- classic RX with single channel output


- STM32F303CCT6
- MPU6050

Weight: 4.6g
Mounting Holes: 3x3cm pattern, with 3.2mm holes (widely compatible)
Voltage: 2-6S

Driver for STM32F303CCT6
Normally you dont need to download any driver for the USB support.
Windows 7 8 and 10 care for this on their own after you connected the device.

The connection diagramm / Pinout you find in KISS-FC GUI.

DOWNLOADS (Manuals, Firmware, GUIs): http://kiss.flyduino.net/downloads/

MinimOSD Arduino OSD Software (kompatibel zu unserem MinimOSD Version) Note: Please extract the KISS_OSD.ZIP and copy the "MAX7456" folder into the "libraries" folder of your Arduino IDE.

MinimOSD Hardware

Connection cable KISS FC -> ESC24A PDB


KISS FC MANUAL by Philipp Seidel

KISS FC 32bit Flight controller V1.03

Not a original

New version
- changed bootloader solderpads to a press button
- changed USB Port type



As we felt the need for a modern more simplified 32bit Flightcontroller, we made the KISS FC, which includes a complete own Flight Controll Firmware development who get rid of some old ballast, this took some time, but the result is very pleasing.
The Idea was to simplify some things and due to intensive long term testings of some pretty good Pilots we where able to optimize the code to a  point where you hopefully get your quad in the air quite quick.
Normally you just need to choose your Airframe in the GUI and are able to fly (at least with KISS ESC), otherwise you can download presets of well knowen Pilots for given configurations and of course can tweak the PID yourself over the GUI.
The software setup side is reduced as far we can, many things are allready taken in to account for you, if you bring some solid soldering skills you should be able to build your quad pretty quick.
A new feature is also the inbuild telemetry, in combination with our 32bit ESC line its possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI
This way you get usefull informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM.


Supported copter types:
- Tri
- Quad +/x
- Hexa +/x

Supported RX types:
- PPM Sum
- Spektrum Sat. (serial / DSM2 & DSMX)
- Futaba / Taranis SBUS
- Jeti ExBus
- Graupner SumD / SumO
- MultiPlex
- classic RX with single channel output


- STM32F303CCT6
- MPU6050

Weight: 4.6g
Mounting Holes: 3x3cm pattern, with 3.2mm holes (widely compatible)
Voltage: 2-6S

Driver for STM32F303CCT6
Normally you dont need to download any driver for the USB support.
Windows 7 8 and 10 care for this on their own after you connected the device.

The connection diagramm / Pinout you find in KISS-FC GUI.

DOWNLOADS (Manuals, Firmware, GUIs): http://kiss.flyduino.net/downloads/

MinimOSD Arduino OSD Software (kompatibel zu unserem MinimOSD Version) Note: Please extract the KISS_OSD.ZIP and copy the "MAX7456" folder into the "libraries" folder of your Arduino IDE.

MinimOSD Hardware

Connection cable KISS FC -> ESC24A PDB


KISS FC MANUAL by Philipp Seidel

APM Flight Controller 5V/12V Dual Output ESC Distribution Power Board

Features:
Dual BEC output,12Vand 5v
Max.support 100A current
Support 6S lipo input
12V BEC could offer power for brushless motor, 5.8G telemetry or FPV camera, 5V offer power for flight controller, Gopro, etc
Each BEC support 2A output,Add heat sink can reach 3A stable output

Package included:
1 x ESC Distribution Power Board

Ublox 7 Series Mini GPS para OPLink CC3D revolución / Naze32 Flip32 / Mini Naze32

• Size: 26mm*21mm
• Weight: 8g
• Wire length: 15cm
• CC3D GPS suitable for CC3D series , the plug is Openpilot Original
• Internal Ublox 7 series chip core of manufacture OEM
• Super mini size, weight only 8g with protective case
• CC3D GPS suitable for CC3D series controller
• Connection diagram:
  Black to GND
  Red to +5V
  White to TX
  Green to RX

GPS Support

Pixhawk RGB LED&USB Extension Module